Sunday, August 29, 2010

A great summer day in Oyster Bay

Saturday August 28th 2010-
While 2 of our volunteers were going over the Alco Worlds Fair Cab display to fix the air horns-clogged baffles, a 3 man crew was hard at work moving the cribbing under the turntables motor frame assembly in order to get to the unprimed areas.

With this task accomplished, they set to work getting a coat of primer on quickly. As the day turned out quite warm, the primer dried in a few hours, so they were able to get a 2nd coat onto the area. They also were able to get 2 coats of primer on all of the brake assembly and platform brackets as well.

A few of our other volunteers were still going over parts inside the storage trailers in order to be able to put together as many sub-assemblies as possible to make it faster to reassemble #35's frame and drive train.


We had one of the locomotive rebuild contractors from Steam Operations Corp (Keith Muldowney) on hand to go over some measurements that were missed on the last visit and to review our progress on parts renewal and breakdowns.

WE (OBRM Volunteers) are on schedule and if the air compressor situation continues at this pace, we should be able to complete the needle scaling of the drive wheels/tender truck assemblies/locomotive frame by the end of November.
One of the drive wheel shas been completely stripped of paint on the outside.Next week the backside will be stripped of the primer that was applied when the new tires were installed, years ago.


We also picked up the rear end of #35's locomotive frame with our trusty forklift in order to move the cribbing underneath. This enabled us to get to the drawbar pin which had been rusted in place for years. We made sure to drain any standing water in the pocket, then we put a jack on a timber under the frame and applied upward force to the pin. From the top, we poured in a "creeping" oil known as "Kroil".
This stuff is amazing and should allow us to pop the pin over the course fo the next few weeks. Then the pin and the pin pocket will get polished while the drawbars will be removed, stripped and coated with cosmoline for long term storage.


Remember that while all of this work is being performed behind the barriers, we are also [color=#FF0000]open for business [/color]and have many familys and railfans visiting with us. Our docents are kept busy with these visitors and we are working diligently on our "SPEND A DAY IN OYSTER BAY" program.

MADDOG

Monday, August 23, 2010

A stellar performance-again!

An overcast day greeted me as I arrived at the display yard around 8am on Saturday 8-21-10.
I started up the forklift and let it warm up while I plotted the days goals.
Putting away the left side valve gear for #35 AND attempting to get the second coat of primer on the turntable motor frame assembly were my goals for the day.

Fortunately, volunteers (you gotta love 'em!) started arriving a t 8:30 and we were able to  accomplish the first goal-valve gear relocation. While the foklift was running, I then put both pilot truck bearing box lock bars onto the work tables. These needed to be cleaned and coated: a simple task, but necessary.

I put a crew on the turntable frame painting and had another of our knowledgable volunteers working on the braking assembly. Many bolts needed to be removed as well as the various sizes of pins which had rotted cotter pins broken off inside of them.
Jeff worked all day getting all of the broken cotter pins removed and had all of the parts given to him completed. This was a dirty job, but he got it done.

At the same time. Paul worked on getting all of the brake assembly parts coated with 2 coats of EXTEND and ready for primer for next weeks work session.
The junior volunteers did a great job of primering the frame and finishing the pilot truck parts
As far as I can see, the pilot truck portion of the restoration has been completed.

Next week-
We will have Keith Muldowny from Steam Operations Corp (S.O.C) paying us a visit to check on our progression of parts renovation for #35.
S.O.C is the contractor for the rebuilding of #35 and as I have already stated-
The more work WE do up in Oyster Bay, the less work THEY (S.O.C) have to do in Alabama. This will translate to more restoration for the same amnount of money!
We plan on getting the painting done on the turntable frame assembly next Saturday and will assemble a new round of parts from #35 to be worked on.
If we can get an air compressor, we will perform paint the removal project on  #35's drive wheels.

Gary

Sunday, August 15, 2010

I''M BACK!!

HI folks-I am back to work! My wedding was wonderful and thank you all for your kind words.
But seriously folks-We had another GREAT day in Oyster Bay!!!
It started off very well and just got better.
We put away the right side valve gear assembly into storage and began work on the left side assembly.
This process was just like the drive rods. We had to remove all of the paint and grind down the surfaces of the parts to bring up their shine and remove all traces of paint & rust. This enables any inspector to see if there are any stress cracks forming which would render the part defective.
Fortunately, by the end of the day the volunteers were able to polish every part and coat them with COSMOLINE for long term storage.

At the same time, the other volunteers were busy at work putting a second coat of EXTEND rust converter onto the turntable motor frame. With the weather being warm & breezy, the extend dried in a couple of hours and they were able to get the first coat of primer onto the assembly. Next week we will get a second coat of primer on and I plan on lifting and re setting the assembly to allow the primer to be applied to the parts under the cribbing.

We will also start paint removal on the drive wheels.
BUT WAIT: THERE'S MORE!!!!!
As an added bonus to the day, OBRM President John Specce stopped by with a present.
#35's ORIGINAL Throttle handle.
Somehow, we were contacted by a gentleman who had it in his possession for some time. He knew about us and wanted to make sure that it was returned to #35 for its restoration.
How's THAT for a great moment in history??!!
Here it is on the tail of the parts trailer going left to right. The throttle grip is on the left side. On the right side is where it attaches to the rod in the cab.

Gary

Thursday, August 5, 2010

Last Saturdays work session 7-31-10

A really beautiful day in Oyster Bay!
We arrived to find both sets of valve gear assemblies waiting to be worked on and we did not dissapoint!
I put two  of our new volunteers to work removing paint and polishing up the right side assembly. After that was completed, they coated the rods with Cosmoline to prep it for a short stay outdoors before it is to be put into storage.
At the same time, we removed the last of the stubborn paint from the turntable motor frame assembly and applied a thick coat of Extend Rust converter. Right now the frame is a light black color, but after the next coat, it should be darker.
When we return to Oyster Bay on Saturday August 14th, we will complete the second coat and by the end of the day, we should have been able to apply the first of two primer coats. Grey is the color of choice!
Gary